Mengenmessung bei kleinem Feststoff/Luft-Verhältnis
Perfekt geeignet für die Steuerung und Regelung von zu dosierender Sorbenzien in Rauchgasbehandlungs- und Transportleitungen mit sehr geringer Materialkonzentration.
- elektrodynamischer Sensor zur Durchflussmessung kleiner Feststoffströme
- Einsatz in pneumatischen Flugstromförderungen
- in Freifallanwendungen mit min. 2 m/s Fallgeschwindigkeit (ca. 25 cm Fallhöhe)
- geeignet für sehr kleine Beladungen
- Verschleißschutz durch keramiküberzogene Antenne
Messung von sehr niedrigen Durchflussmengen
- Features & Benefits
- Main applications
- Technical Specifications
- Technical Data
- Mounting Installation
- Downloads
- Particularly good in pneumatic applications for material flow rates from a few g/h up to a few hundreds kg/h (depending on application)
- Very reliable for free-fall applications with a drop speed of at least 2 m/s (approx. 25 cm drop height)
- In cases where dust measuring instruments cannot cope and flow rate measuring instruments are overspecified
- The PicoFlow is perfectly suited for industrial applications especially in power generation or cement plants where it can be used to regulate or control additional reagent in flue gas treatment: injection of activated carbon, minsorb, lignite coke…
- Waste incineration
- Steel
- Chemistry
- Energy
- Cement
- Pharma
Technical Specifications | |
---|---|
Material to measure | Dust, powders or granulates max. grain size 10 mm |
Working principle | Electrodynamic |
Process pressure | max. 10 bar |
Process temperature | +150°C |
Mounting | Via process connection |
Type of Conveying | Pneumatic leanphase, vertical freefall after feeder |
Flow rates | Depending on application |
Pipe diameter | Max. 1000 mm |
ATEX rating | Category 1/2 |
Output | 4…20mA, Modbus, Profibus |
- Pneumatic conveying and free fall
- Absolute measurements in g/h or kg/h
- Materials: all types of dust, powder and granules
- Wear-resistent
Sensor Technical Data | |
---|---|
Housing | Aluminium |
Protection Type | IP 66; ATEX: Cat. 1/2 GD |
Operation temperature | Process: -20 … +150 °C Ambient: -20 … + 60 °C |
Max. working pressure | 10 bar |
Weight | 1,5 kg |
Sensor rod | Stainless steel, ceramic coated, max. 450 mm |
Accuracy | ± 5 % in calibrated range |
Transmitter Technical Data | ||||
---|---|---|---|---|
Transmitter (DIN Rail) | Transmitter (field housing) | |||
Power supply | 24 V DC ±10 % | 110 / 230 V AC 50 Hz (optional 24 V DC) |
||
Power consumption | 20 W / 24 VA | |||
Protection type | IP 40 to EN 60 529 | IP 65 to EN 60 529/10.91 | ||
Ambient operating temperature | -10 … +45 °C | |||
Dimensions (W x H x D) | 23 x 90 x 118 mm | 258 x 237 x 174 mm | ||
Weight | Approx. 172 g | Approx. 2.5 kg | ||
Connection terminals cable cross-section |
0.2-2.5 mm2 [AWG 24-14] | |||
Current output | 1 x 4 … 20 mA (0 … 20 mA), load < 500 Ω |
3 x 4 … 20 mA (0 … 20 mA), load < 500 Ω |
||
Interface | RS 485 (ModBus RTU) / USB | |||
Pulse output | Open collector – max. 30 V, 20 mA | |||
Relay contact | Max. rated load: 250 V AC Max. peak current: 6 A Max. rated load 230 V AC: 250 VA Max. breaking capacity DC1: 3/110/220 V: 3/0.35/0.2 A Min. switching load: 500 mW (10 V / 5 mA) |
|||
Data backup | Flash memory |
The PicoFlow can be installed in metallic ducts and pipelines.
It should be installed as far as possible away from curves and other fittings such as valves and slides. The distance between the sensor rod and fittings in the duct should be at least three times the duct diameter in every flow direction. Non-metallic ducts must be cased with a metal sleeve, a metal foil or a tight-mesh metal grille over a length of at least five times the duct diameter. |